|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Delivery came quite promptly and in a very readable format. Thank you.
;
I found my Clarion VRX8370R in the Camper I bought and I wasn't able for month to understand it.
The Owner Manual was perfect and just what I was searching for.
Thank you.
Leonardo
;
Very good copy of Manual, clear and easy to print off, arrived very promptly and reasonably priced.
Thanks, I will use you again.
;
Zeer duidelijke afdrukken op A4-formaat , zeer uitgebreide handleiding . Pluspunt ,zeer snelle
respons van jullie , binnen de 24h . Top !!!
;
I AM HIGHLY IMPRESSED BY THE EASE OF USE OF THIS DOWNLOAD SERVICE. INSTRUCTIONS ARE CLEAR AND SIMPLE TO FOLLOW....EVEN BY TECHNOPHOBES SUCH AS MYSELF. THE EMAILS POINT YOU IN THE RIGHT DIRECTION...ITS SO EASY PEASY. THE DOWNLOAD CHOICE OF USER MANUALS IS EXTENSIVE AND I COULD NOT FIND A CHEAPER OR MORE EFFICIENT SERVICE ON THE INTERNET. I COULD NOT HAVE MADE A BETTER CHOICE OF INFORMATION PROVIDER. SHOULD I EVER NEED ANOTHER USER MANUAL, THEN THIS IS THE FIRST CHOICE SITE. COULD NOT BE BETTER PLEASED!!!!!!!...MANY THANXES FROM JIM BURNS
Installation and Connections
To prevent possible damage to your speakers and other components in your audio system, it is important that ALL components, including the FL 8370 and your receiver or preamp and amplifiers, are turned off and unplugged from their AC power source when installing any new component. Connecting the FL 8370 to your audio system is simple. Using standard RCA-to-RCA interconnect cords, connect the left and right Audio Output jacks � on the rear panel to the CD input jacks on your receiver, surround processor or preamplifier. If your system includes an optional external digital-to-analog converter, or if you are using a receiver or other processor that has the capability to decode PCM digital input signals, connect the Coaxial-Digital Output jack � to the Coaxial-Digital input on the decoder. Make certain to use a coaxial-style interconnect cable, as standard audio cables will not perform as well. Install the two AA batteries supplied with the FL 8370�s remote by turning the remote over so that you are holding the bottom side up. Press lightly on the embossed arrow on the cover and gently slide the cover towards you in the direction of the arrow. Insert the batteries inside the compartment, being careful to follow the + and � polarity indications at the bottom of the compartment. Replace the cover by placing it on the remote and sliding it back towards the top of the remote. NOTE: When replacing batteries it is always a good idea to replace both at the same time. When the unit will not be used for an extended period of time, it is also a good idea to remove the batteries so that the potential for corrosion or damage is avoided. If the FL 8370 is installed behind a cabinet or other obstruction that may block the path between the front-panel Remote Sensor and the location of the remote, an optional external IR sensor may be used. Connect the sensor to the remote IR-In Jack ¢ on the rear panel. This jack may also be connected to the IR-Output jack of another compatible Harman Kardon component or a compartible IR-systemremote product.
©
You may also use the IR Sensor in the FL 8370 to send commands to other compatible remote controlled products. Connect the Remote IR-Out jack £ to the input of the other product or system. Connect the power to a nonswitched AC wall outlet or to the accessory outlet on the rear of another audio device in your system and you are ready to go! NOTE: When using the accessory outlet on another product to power the FL 8370 make certain that it has the compatibility to power a device that draws at least 20 watts of current in addition to being able to handle the requirements of the other devices that may be plugged into the accessory outlets. If you use a �switched� outlet, it is important to remember that the host product must be turned on in order for the FL 8370 to operate.
9 INSTALLATION AND CONNECTIONS
|
|
|
> |
|
